Frigidaire Appliance Repair Ottawa
Frigidaire appliance repair in Ottawa for electric washers, dryers, dishwashers, fridges, freezers, microwaves, ovens, cooktops, and stove/ranges. We diagnose Frigidaire error codes, drain problems, leak codes, airflow and no-heat issues, cooling faults, door and latch faults, sensors, thermistors, wiring, and control boards — with clear pricing and a 90-day labour warranty.
We also repair many other brands across Ottawa.
Why Choose Fixer for Frigidaire
- Frigidaire-specific diagnostics — we trace the real cause before replacing expensive parts: sensors, pumps, fans, heaters, door locks, wiring, and control boards.
- Electric Frigidaire appliance service only — washers, dryers, dishwashers, fridges, freezers, microwaves, ovens, cooktops, and electric ranges. No gas work.
- Error-code troubleshooting — common Frigidaire E-codes, i-codes, F-codes, SY EF, H1, and PF on laundry, kitchen, and cooking appliances.
- Local Ottawa service — Kanata, Stittsville, Nepean, Barrhaven, Orleans, Vanier, and nearby areas with clear repair recommendations.
Frigidaire Appliances We Repair
Frigidaire Washers
From E10 fill faults and E20 drain issues to E47 door lock codes, we repair Frigidaire washers across Ottawa.
Frigidaire Dryers
E64 heating faults, E71 thermistor codes, and AF vent warnings on Frigidaire electric dryers are common calls we handle.
Frigidaire Dishwashers
i10 fill faults, i20 drain codes, i30 leak warnings, and UF vent fan faults on Frigidaire dishwashers are repaired by our Ottawa team.
Frigidaire Refrigerators
SY EF fan faults, H1 temperature alarms, and dF defrost messages on Frigidaire fridges — electrical diagnosis only; Fixer does not perform sealed-system refrigerant repairs.
Frigidaire Freezers
H1 temperature alarms, EF fan faults, and dF defrost issues on Frigidaire freezers need prompt attention — electrical diagnosis only.
Frigidaire Microwaves
F-series control faults and door latch warnings on Frigidaire microwaves — safe professional service only.
Frigidaire Ovens
F10, F30, F90, and F95 codes on Frigidaire electric ovens are common repair requests — no gas oven service.
Frigidaire Cooktops
Zone and control faults on Frigidaire electric cooktops need careful diagnosis — no gas cooktop service.
Frigidaire Stoves / Ranges
Freestanding Frigidaire electric ranges with oven or surface element faults are repaired with a 90-day labour warranty.
Common Frigidaire Error Codes
Frigidaire display codes differ by model line and appliance type. These are frequent E-codes, i-codes, F-codes, SY messages, and power warnings our Ottawa technicians see on Frigidaire washers, dryers, dishwashers, refrigerators, freezers, microwaves, ovens, cooktops, and electric ranges. Use them as a starting point — not a final diagnosis — before booking service in Ottawa, Kanata, Stittsville, Nepean, Orleans, Barrhaven, and nearby areas.
These codes are a starting point, not a final diagnosis. If the code returns after one basic reset, it is safer to stop using the appliance and book a proper inspection.
Frigidaire Washer Error Codes
Fill, drain, door-lock, and motor-drive E-codes are among the most common Frigidaire washer calls we handle in Ottawa homes.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| E10 / E11 | The washer is taking too long to fill, or inlet flow is lower than the control expects for the selected cycle. | Confirm both supply taps are fully open and inlet hoses are not kinked. Check inlet screens for sediment if you can access them safely. Cancel the cycle and avoid forcing repeated starts. | If filling stays slow or the code returns, Fixer can diagnose inlet valves, pressure sensing, wiring, and control-board output before parts are replaced unnecessarily. |
| E20 / E21 | The washer is not draining correctly, or the control does not see the water level dropping during the drain step. | Confirm the drain hose is not kinked or pushed too far into the standpipe. Clean the drain pump filter if your model has an accessible filter. Do not keep restarting if water remains in the drum. | If E20 or E21 comes back, Fixer can diagnose the drain pump, blockage, wiring, pressure system, and control-board output. |
| E23 / E24 | A drain pump, motor drive, or control output fault is preventing normal drain or drum movement on this electric washer. | Stop the cycle, unplug the washer, and avoid repeated reset attempts. Note whether the code appears at start, mid-wash, or spin. | Fixer can test pump drive, motor feedback, wiring, and control-board signals before expensive parts are ordered. |
| E35 | The control detected an overfill condition — water level rose higher than expected during fill. | Cancel the cycle and watch for active inlet leaking. Shut off the water supply if fill continues. Use the recommended detergent amount. | Fixer can trace inlet valves, pressure switches, float systems, and control fill output rather than guessing at parts. |
| E40 / E41 | The door is not closed firmly enough, or the door switch does not confirm a closed door before the cycle advances. | Close the door firmly and check the seal for debris. Power off for one minute, then try again once. Do not force the door open while a lock is active. | If the door will not register as closed, Fixer can test door switches, latch alignment, wiring, and control interlocks. |
| E47 | The door lock is not engaging, not releasing, or the control does not receive a confirmed locked-door signal. | Close the door firmly and make sure nothing is caught in the seal. Power off for one minute, then try again once. Do not bypass the door lock. | Fixer can test the door lock assembly, wiring harness, and control output safely before the lock is replaced. |
| E52 | A motor, inverter, or drive communication fault is preventing normal drum movement on this electric washer. | Stop the cycle, unplug the washer, and avoid stacking repeated cycles. Do not attempt to open the motor or inverter area yourself. | Motor and drive faults need proper testing. Fixer can inspect motor feedback, wiring, and control-board drive output. |
| E59 | The control is not detecting expected motor speed or tacho feedback during wash or spin. | Power off, unplug the washer, and avoid repeated reset attempts. Note when the code appears in the cycle. | Fixer can diagnose motor speed feedback, wiring, and control-board inputs before drive components are replaced. |
Book Frigidaire Washer repair in Ottawa · View appliance error code guide
Frigidaire Dryer Error Codes
Heating, thermistor, airflow, and power E-codes are especially common on Frigidaire electric dryers in Ottawa homes with long or blocked vent runs. Fixer services electric dryers only — no gas dryer repair.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| E64 | A heating element or heater circuit fault was detected on this electric dryer. | Reset the breaker once, wait 60 seconds, and run one short timed dry. Confirm a heat cycle is selected — not air fluff only. | Fixer can diagnose heating elements, fuses, relays, wiring, and control-board output before parts are replaced. |
| E65 | A heater relay or control output fault is preventing the dryer from energizing the heating circuit. | Reset the breaker once and note whether the code appears at startup or mid-cycle. Check lint filter and exterior vent airflow. | Fixer can test relay operation, control-board output, wiring, and terminal connections on electric dryers. |
| E66 | A high-limit or heat safety circuit fault was detected that can shut off heat to protect the appliance. | Allow the dryer to cool. Clean the lint filter and confirm strong exhaust airflow at the exterior vent cap. | Fixer can trace high-limit devices, thermistors, vent airflow, and control safety logic. |
| E68 | A stuck key or control input fault was detected on the dryer user interface. | Wipe the control panel dry and press each button once to release any stuck keys. Reset power once. | If E68 returns on a dry panel, Fixer can diagnose touch panels, control inputs, and board communication. |
| E71 / E72 | A thermistor or temperature sensor reading is out of range, which can shut off heat or end the cycle early. | Clean the lint filter and confirm strong exhaust airflow at the exterior vent cap. Run one timed dry cycle after a basic reset. | Fixer can diagnose thermistors, wiring, and control-board inputs rather than replacing sensors by guesswork. |
| AF / restricted airflow | The dryer detected restricted airflow through the vent system, which can extend dry times and trigger shutdowns. | Clean the lint screen, inspect the vent hose behind the dryer, and confirm the exterior cap opens when the dryer runs. | If AF or vent warnings return after basic cleaning, Fixer can check vent routing, sensors, heating circuits, and control feedback. |
| Door switch | The door interlock does not confirm a closed door, so the dryer will not tumble or heat. | Close the door firmly and check the latch area for lint or debris. Power cycle once. Do not bypass the door switch. | Fixer can test door switches, wiring, and control interlocks on electric dryers. |
| No heat group | The dryer tumbles but does not heat, often related to heating elements, fuses, thermistors, relays, or control output on electric models. | Confirm a heat cycle is selected — not air fluff or cool down only. Reset the breaker once. Check lint filter and exterior vent airflow. | No-heat complaints on electric Frigidaire dryers need element, fuse, relay, and wiring diagnosis before parts are replaced. |
Book Frigidaire Dryer repair in Ottawa · View appliance error code guide
Frigidaire Dishwasher Error Codes
Fill, drain, leak, and heating i-codes are common on Frigidaire dishwashers in Ottawa. Exact i-code meanings vary by model series.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| i10 | The dishwasher is not filling within the expected time, or inlet flow is too low for the selected cycle. | Confirm the water supply tap under the sink is fully open and the inlet hose is not kinked. Cancel the cycle and avoid repeated forced starts. | If i10 returns, Fixer can diagnose inlet valves, float switches, wiring, and control-board fill output. |
| i20 | A drain pump or drain path fault was detected — water is not leaving the tub as expected. | Check the sink drain and disposal for blockages. Clean the filter at the tub bottom if accessible. Do not run another cycle with standing water. | Fixer can test drain pumps, obstructions, wiring, and control-board output before parts are replaced. |
| i30 | The dishwasher detected water in the base pan, an active leak, or a float condition that stops the cycle to limit water damage. | Shut off the water supply, cancel the cycle, and watch for active inlet leaking. Use the recommended detergent amount. | If leaking or float warnings continue, Fixer can trace inlet valves, hose connections, pump seals, and tub integrity. |
| i40 | A water level or pressure sensing fault was detected during fill or wash stages. | Confirm hot water at the kitchen tap and that the supply tap is fully open. Run one normal cycle after a power reset. | Fixer can diagnose pressure switches, fill timing, wiring, and control-board signals. |
| i50 | A wash motor, circulation pump, or drive communication fault is preventing normal spray or drain motor operation. | Stop the cycle and unplug the dishwasher. Do not run another cycle with standing water in the tub. | Fixer can test motor drive, pump obstructions, wiring, and control-board output before parts are replaced. |
| i60 | The heating circuit did not reach the expected temperature during wash or dry stages, or dry performance is poor. | Use a normal hot-water cycle and confirm hot water at the kitchen tap first. Avoid running heated dry repeatedly while the fault is present. | Heater, thermostat, and control-board faults need proper testing. Fixer can check the heating circuit safely on electric dishwashers. |
| i70 | A thermistor or temperature sensor reading is out of range during wash or dry stages. | Run hot water at the kitchen tap for 30 seconds before starting a cycle. Power cycle once at the breaker. | Fixer can diagnose sensor circuits, wiring, and control-board inputs on electric dishwashers. |
| UF / vent fan | A vent fan or drying airflow fault was detected during heated dry on models with an external or internal vent fan. | Cancel heated dry and run one rinse cycle as a test. Confirm the dishwasher is installed with proper vent routing if your model vents outside. | Fixer can diagnose vent fans, drying circuits, wiring, and control output on electric dishwashers. |
Book Frigidaire Dishwasher repair in Ottawa · View appliance error code guide
Frigidaire Refrigerator Error Codes
SY messages, fan faults, defrost issues, and temperature alarms are common on Frigidaire fridges in Ottawa. Many codes are electrical — not sealed-system failures.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| SY EF | A communication or evaporator fan fault was detected — the fan may not be running at the speed the control expects. | Listen for fan noise at the back or inside the fridge. Confirm vents inside the cabinet are not blocked by food. Power off for two minutes, then restore once. | If cooling is weak and SY EF returns, Fixer can diagnose fan motors, wiring, and control-board output. Fixer does not perform sealed-system refrigerant repairs. |
| SY CE | A communication fault between control boards or display modules was detected. | Power off for two minutes, then restore once. Note whether the display is blank, frozen, or showing conflicting temperatures. | Fixer can diagnose control communication, wiring harnesses, and board inputs electrically. Sealed-system work is outside our scope. |
| H1 / HI | The refrigerator is reporting high temperatures or a cooling performance alarm outside expected limits. | Confirm doors close fully on both sections and interior vents are not blocked. Avoid packing warm food in large batches while troubleshooting. | Fixer can diagnose fans, sensors, defrost circuits, and control logic electrically. Sealed-system compressor or refrigerant repairs are not performed by Fixer. |
| OP | A door-ajar or open-door condition was detected long enough to affect cooling performance. | Close doors firmly and confirm the alarm silences. Check gasket condition and that bins are not blocking the seal. | If OP alarms repeat on closed doors, Fixer can test door switches, sensors, fans, and control logic. |
| SH | Showroom, demo, or hospitality mode may be active, which can affect cooling display or compressor run patterns on some Frigidaire models. | Review your manual for how to exit demo or showroom mode. Power cycle once after confirming mode settings. | If cooling does not return after mode is cleared, Fixer can verify control settings and electrical circuits before assuming a sealed-system failure. |
| EF / fan | An evaporator or condenser fan is not running at the speed the control expects, which can reduce cooling performance. | Listen for fan noise and keep air vents clear. Power off for two minutes, then restore once. | Fixer can test fan motors, wiring, and control-board output. We do not perform sealed-system refrigerant repairs. |
| dF / defrost | A defrost system fault was detected. Frost buildup can follow if defrost does not complete on schedule. | Check for heavy frost on the rear wall of the freezer. Avoid chipping ice with tools. Keep doors closed as much as possible until service is booked. | Fixer can test defrost heaters, sensors, wiring, and control-board defrost scheduling. Sealed-system refrigerant repairs are not performed by Fixer. |
Book Frigidaire Refrigerator repair in Ottawa · View appliance error code guide
Frigidaire Freezer Error Codes
Temperature alarms, fan faults, and frost issues are common Frigidaire freezer calls in Ottawa — many are diagnosable without sealed-system work.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| H1 / HI | The freezer detected a temperature rise or high-temperature alarm long enough to affect food safety. | Close the lid or door firmly and confirm the alarm silences. Check gasket condition and that bins are not blocking the seal. | If alarms repeat on a closed door or temperatures stay warm, Fixer can test door switches, sensors, fans, and control logic. |
| OP | A door-ajar or open-door condition was detected on the freezer compartment. | Close the door firmly and allow temperatures to stabilize for several hours. Keep vents clear inside the cabinet. | If OP returns with the door closed, Fixer can diagnose door switches, gaskets, and control inputs. |
| SY EF / EF | A freezer fan fault was detected — the fan may not be running at the speed the control expects. | Listen for fan noise and keep air vents clear. Power off for two minutes, then restore once. | Fixer can test fan motors, wiring, and control-board output. Sealed-system work is outside our scope. |
| dF | A defrost cycle did not complete as expected. Heavy frost can reduce airflow and cooling performance. | Do not chip ice with sharp tools. Keep the door closed and note whether frost covers the rear wall or vents. | Fixer can diagnose defrost heaters, sensors, and control scheduling on electric freezers. We do not perform sealed-system refrigerant repairs. |
| Sensor / thermistor group | A temperature sensor or thermistor fault was detected that can affect cooling commands and alarm thresholds. | Allow the freezer to stabilize after a power event. Keep vents clear and avoid leaving the door open during troubleshooting. | Fixer can test sensor circuits, wiring, and control-board inputs electrically. |
| Control / display warning | The control or display reported a fault that may affect temperature readouts or cooling commands. | Power cycle once at the breaker. Review your manual for control lock or demo settings that can affect cooling display. | If cooling does not return, Fixer can verify control settings and electrical circuits before assuming a sealed-system failure. |
Book Frigidaire Freezer repair in Ottawa · View appliance error code guide
Frigidaire Microwave Error Codes
Control, sensor, and door faults are common on Frigidaire microwaves. Internal high-voltage components make professional service essential — do not open the cabinet.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| F1 | A control-board or relay control signal problem was detected. | Reset power once at the breaker or unplug for one minute. Do not remove the cover or probe internal wiring. | If F1 returns, microwave internal diagnosis should be handled by a technician because high-voltage parts can remain dangerous even when unplugged. |
| F2 | A temperature or sensor-related fault was detected depending on model. | Reset power once and make sure the microwave cavity is clean and dry. Do not open the cabinet. | Fixer can diagnose sensor circuits, wiring, and control-board faults safely. Internal components can hold dangerous high voltage even when unplugged. |
| F3 | A keypad or touch-panel communication fault may be preventing normal input to the control board. | Wipe the panel dry, unplug for one minute, and try once more. Do not disassemble the control panel. | Microwave internal components can hold dangerous high voltage even when unplugged. Fixer can test the keypad and control board safely. |
| F4 | A humidity or moisture sensor on the control surface may be reading out of range, often after steam or spills. | Dry the exterior thoroughly and avoid spraying cleaners into button edges. Reset power once. | If F4 returns on a dry panel, book service to test sensors and control inputs — not a homeowner repair. High voltage may remain inside the unit. |
| PF | A power interruption or unstable supply was detected during operation. | Confirm the outlet works for another small appliance and reset the breaker once. Run a 10-second test with a cup of water only. | Repeated PF codes may indicate supply or control-board issues. Internal microwave components can hold dangerous high voltage — leave testing to a technician. |
| Door / latch warning | The microwave believes the door is open when heat or cook functions are requested. | Inspect the door hooks and latch area for debris. Close the door firmly once and avoid slamming. | If the display still shows a door fault, Fixer can test door switches and latch alignment. Capacitors can retain high voltage after unplugging. |
Book Frigidaire Microwave repair in Ottawa · View appliance error code guide
Frigidaire Oven Error Codes
Control, sensor, and heating F-codes on Frigidaire electric ovens are common in Ottawa. Fixer services electric ovens only — no gas oven repair.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| F10 | The oven may be reading a runaway heat or over-temperature condition and has shut down heat to protect the appliance. | Turn the oven off and let it cool completely. Do not keep using the oven if heat seems uncontrolled. | Fixer can trace sensor feedback, relay operation, and control logic on electric ovens. |
| F11 | A stuck key or keypad fault was detected on the oven control panel. | Wipe the panel dry and press each button once to release any stuck keys. Reset power once at the breaker. | If F11 returns on a dry panel, Fixer can diagnose touch panels, control inputs, and board communication. |
| F12 | A keypad or user-interface fault was detected that can limit bake, broil, or timer input on the oven control. | Wipe the panel clean and dry. Reset power once and avoid pressing keys that feel stuck. | Fixer can diagnose keypad circuits, control inputs, and board communication before the panel is replaced. |
| F13 | A control-board or electronic control fault was detected that can stop bake, broil, or display functions. | Power off at the breaker for two minutes, then restore once. Avoid running self-clean while a control code is active. | Fixer can diagnose control boards, wiring, and relay outputs on electric Frigidaire ovens before expensive boards are replaced. |
| F14 / F15 | A control communication or EEPROM fault was detected between oven control modules. | Power off at the breaker for two minutes, then restore once. Note whether the display is blank or frozen. | Fixer can diagnose control communication, wiring harnesses, and board inputs on electric ovens. |
| F3 / F20 / F26 | A communication fault between oven control modules or display boards was detected on some Frigidaire models. | Reset the breaker once and avoid repeated power cycling. Note whether the display is blank, frozen, or unresponsive. | Fixer can diagnose user-interface boards, main control, wiring harnesses, and module communication. |
| F30 / F31 | An oven temperature sensor or probe circuit is not reporting a stable reading to the control board. | Allow the oven to cool. Make sure the sensor area inside the cavity is not blocked by cookware or touching the wall. | Fixer can diagnose sensor circuits, connectors, and control-board inputs on electric ovens — no gas supply work. |
| F90 / F91 / F92 / F93 / F94 | The oven door latch or lock did not reach the position the control expects, or a self-clean or heating safety interlock fault was detected. | Let the oven cool completely. Cancel self-clean if active and do not force the door open. | If the door stays locked or the code returns, Fixer can test lock assemblies, latch switches, wiring, and control interlocks safely. |
| LOC / control lock | Child lock or control lock is active, limiting keypad input or preventing accidental cycle changes. | Review your manual for how to clear control lock. Hold the lock button combination shown on the display if applicable. | If the lock will not clear or the display stays unresponsive, Fixer can diagnose keypad, user interface, and control-board communication. |
Book Frigidaire Oven repair in Ottawa · View appliance error code guide
Frigidaire Cooktop Error Codes
Zone and control faults on Frigidaire electric cooktops are common calls. Fixer services electric cooktops only — no gas cooktop, valve, or supply repair.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| F1 / control fault | A control or touch-control fault was detected that can stop one or more radiant zones from heating or responding. | Reset the breaker once, wait 60 seconds, then restore power. Wipe the glass surface and control panel dry. | Fixer can diagnose touch controls, relays, wiring, and control-board communication on electric cooktops. |
| F11 | A stuck key or touch-panel fault was detected that can freeze zone selection or power changes. | Wipe the panel clean and dry. Reset power once and avoid pressing keys that feel stuck. | Fixer can diagnose touch panels, control inputs, and board communication before the glass assembly is replaced. |
| F3 / F20 / F26 | A communication fault between cooking controls or modules was detected on some Frigidaire cooktop models. | Reset the breaker once and avoid repeated power cycling. Note whether the display is blank or frozen. | Fixer can diagnose user-interface boards, main control, wiring harnesses, and module communication. |
| F40 / F41 | A cooktop lockout or lock-control fault is preventing zone changes or surface operation. | Review your manual for control lock instructions. Do not force controls or bypass the lock. | Fixer can diagnose touch panels, lock control circuits, and control-board inputs on electric cooktops. |
| F10 / over-temperature warning | The control may be reading an unsafe or unexpected surface temperature and has shut down a zone for protection. | Turn off the cooktop and let it cool completely. Stop using the zone if heat seems uncontrolled. | Fixer can diagnose temperature sensors, limiters, relays, wiring, and control output on electric cooktops. |
| Surface element not heating | A radiant zone powers on at the display but does not heat, often related to the element, relay, switch, or wiring on this electric cooktop. | Try a different zone at the same power level. Reset the breaker once and confirm the correct zone is selected. | Fixer can diagnose radiant elements, relays, switches, and connections — no gas burner repair. |
| Surface hot / indicator warning | A hot-surface indicator is stuck on or a residual-heat warning persists after the zone has cooled. | Allow the surface to cool fully before wiping. Do not place items on zones showing a hot indicator. | If warnings return on a cold surface, Fixer can diagnose temperature limiters, sensors, and control feedback. |
Book Frigidaire Cooktop repair in Ottawa · View appliance error code guide
Frigidaire Stove / Range Error Codes
Freestanding Frigidaire electric ranges combine oven and surface cooking on one control — faults can affect either section. No gas burner repair.
| Code | What it may mean | Safe check | When to call Fixer |
|---|---|---|---|
| F1 / control fault | A shared range control or touch-panel fault was detected affecting oven, surface, or timer functions. | Reset the breaker once, wait 60 seconds, then restore power. Wipe the control panel dry. | Fixer can diagnose touch controls, relays, wiring, and control-board communication on electric ranges before boards are replaced. |
| F10 / runaway heat or over-temperature | The oven section may be reporting a runaway heat or over-temperature condition that shut down heat on the range. | Turn the oven off and let it cool. Do not continue baking if the range exterior feels hotter than usual. | Fixer can trace oven sensor feedback, relay output, and shared control logic on electric ranges. |
| F13 / control memory or board fault | A control-board or memory fault was detected on the shared range control that can affect oven and surface settings. | Power off at the breaker for two minutes, then restore once. Note whether the fault appears on the oven, cooktop, or both. | Fixer can diagnose control boards, wiring, and relay outputs on electric Frigidaire ranges before expensive boards are ordered. |
| F30 / F31 | An oven temperature sensor on the range is not reporting a stable reading to the shared control. | Allow the oven to cool. Make sure nothing inside the oven cavity is touching the sensor area. | Fixer can diagnose sensor circuits, connectors, and control inputs on the oven portion of electric ranges. |
| F40 / F41 | A cooktop lockout or surface control fault is limiting zone changes or radiant element operation on the range. | Review your manual for control lock instructions. Do not force controls or bypass the lock. | Fixer can diagnose touch panels, lock control circuits, and control-board inputs on the surface section of electric ranges. |
| F90 / F91 / F92 / F93 / F94 | The oven door latch or lock on the range did not engage, release, or confirm as expected during bake or self-clean. | Let the oven cool. Cancel self-clean if active and do not force the door. Review your manual for lock release steps. | If the lock will not release or codes return, Fixer can test lock assemblies, latch switches, and control interlocks on electric ranges. |
| LOC / control lock | Child lock or control lock on the range is active, limiting oven or surface keypad input. | Review your manual for how to clear control lock on your range model. Power cycle once if the display is frozen. | If the lock will not clear, Fixer can diagnose keypad, user interface, and shared control-board communication. |
| Surface element not heating | A cooktop burner or radiant zone on the range does not heat while the display shows it is on. | Try another zone at the same setting. Reset the breaker once and confirm the correct zone is selected. | Fixer can diagnose surface elements, switches, and wiring on electric ranges. We do not service gas burners or gas supply. |
Book Frigidaire Stove / Range repair in Ottawa · View appliance error code guide
Frigidaire error code came back?
Fixer Appliance Repair can diagnose Frigidaire electric appliances in Ottawa and nearby areas, including drain pumps, door locks, fans, sensors, heating circuits, wiring, and control boards. If the code returns, it is better to book a proper diagnosis before replacing parts.
Service Areas
We repair Frigidaire appliances across Ottawa and nearby communities.
Common Frigidaire Problems We Fix
Frigidaire washers not filling or draining
E10, E20, E23, and E47 codes often point to inlet valves, drain pumps, pressure sensing, or door locks — we diagnose before parts are replaced.
Frigidaire dryers not heating or venting
E64, E71, AF, and thermistor codes on Frigidaire electric dryers need vent, heating circuit, and control-board testing.
Frigidaire dishwashers not cleaning or draining
i10, i20, i30, and i50 codes on Frigidaire dishwashers are traced to pumps, inlet paths, float switches, heaters, and control signals.
Frigidaire refrigerators not cooling properly
SY EF, H1, EF, and dF messages on Frigidaire fridges can be tested electrically. Sealed-system refrigerant repairs are not performed by Fixer.
Frigidaire ovens and ranges not heating
F10, F30, F90, and F95 codes on electric Frigidaire ovens and ranges often relate to sensors, elements, relays, or control boards.
Frigidaire microwaves with control or door faults
F1–F4 and door-latch codes on Frigidaire microwaves involve safety interlocks and high voltage — professional service only.
Related Frigidaire appliance services
Jump to our main service pages for Frigidaire repair in Ottawa.
Induction repair
Electric induction only — no gas appliance service.
Frigidaire repair by area
See local coverage and neighbourhood pages near you.
Frigidaire error codes & troubleshooting
Look up Frigidaire codes and related guides.
More brands
FAQ
What should I do if my Frigidaire washer shows E10, E20, E40, or E52?
Try one basic reset and check only safe items like the drain hose, water taps, door seal, and visible filter if your model has one. If the code returns, Fixer can diagnose the inlet valve, drain pump, door lock, pressure system, wiring, and control-board output before parts are replaced unnecessarily.
Can Fixer diagnose Frigidaire dishwasher i20, i30, or i50 codes?
Yes. For Frigidaire dishwashers, Fixer can check drain pumps, float switches, wash motors, heating circuits, wiring, terminal connections, and control-board output.
Do Frigidaire fridge or freezer SY EF, H1, or dF codes always mean sealed-system repair?
No. Many Frigidaire cooling messages are related to fans, sensors, frost buildup, defrost parts, power events, wiring, or control boards. Fixer can diagnose electrical, fan, sensor, drain, defrost, and control issues. Fixer does not perform sealed-system refrigerant repairs.
Are Frigidaire microwave F-codes safe to repair myself?
No. Microwave internal components can hold dangerous high voltage even when unplugged. You can safely reset power once and check the door/latch area for debris, but internal diagnosis should be handled by a technician.
Is there a 90-day labour warranty?
Every completed repair includes a 90-day labour warranty.
Book Frigidaire Appliance Repair
Need Frigidaire appliance repair in Ottawa? Call Fixer Appliance Repair — same-day options may be available.